Fire alarm for Calgary contractorsYou pull the wire. We handle the fire alarm side.
On a Calgary new build or tenant improvement, we work alongside your electrical crew and take the fire alarm from device layout through panel supply, programming and terminations to CAN/ULC-S537 verification, with the documents the inspector asks for. Send us the drawings and we quote it in writing.
- Authorized Autocall distributor
- Device layout that meets code the first time
- Kitchen suppression and extinguishers on the same job
- Kidde
- Badger
- Amerex
- Buckeye
- ProTex II
- CaptiveAire
- Autocall
Who does what on a fire alarm job?
Your crew runs the conduit and pulls the cable; we supply the panel, lay out the devices, terminate and program, then verify the system and hand over the paperwork. Here's the usual split.
| Stage | Electrical contractor | Defense Fire Protection |
|---|---|---|
| Design and layout | Supplies drawings | Device layout to code, panel selection, quote |
| Rough-in | Boxes, conduit, wire pull | Answers layout questions on site |
| Panel and devices | Mounts as agreed | Supplies the panel, terminations and programming |
| Tie-ins | Power, shutdown circuits | Kitchen and special-hazard suppression release, sprinkler tie-ins |
| Verification | On site for corrections | CAN/ULC-S537 verification and report for the inspector |
| After occupancy | - | Yearly CAN/ULC-S536 inspection for the owner, if they want us |
Every project is split a little differently; we agree the scope line by line in the written quote.
Why we spec Autocall panels on Calgary projects
Because addressable Autocall panels make the job cheaper to wire and easier to verify. Every device is individually supervised, T-tapping allows more efficient wire runs, and the 4100ES arrives custom-built and ready to connect.
- 4007ES for small to mid-size buildings, up to 250 addressable points, and for conventional panel upgrades without rewiring
- 4010ES for mid-size and growing sites, 250 to 1,000 points
- 4100ES for large facilities, up to 3,000 points with integrated voice evacuation
- BACnet and Modbus for building automation, and listed suppression release on the 4007ES and 4100ES
We are an authorized Autocall distributor, so the panel, the programming and the verification all come from one place. Compare Autocall panels →
More than the alarm: suppression and extinguishers for new builds and TIs
A restaurant fit-out or a shop with a spray booth needs more than a fire alarm, and the tie-in between systems is where inspections fail. We supply and install those systems too, so one sub carries the whole fire protection scope.
Kitchen hood suppression
New systems for new restaurants, renovations and line changes, coordinated with you and the electrician. Typically $6,000 to $12,000 installed, usually including stamped engineered drawings and the permit; the electrical scope (shutting down outlets and make-up air, local bell) and installing the gas valve are done by others.
The suppression-to-alarm tie-in
In Alberta, if the building has a fire alarm, a kitchen suppression system must activate it on discharge. We wire and test that connection, so it's verified once and nobody points at the other trade.
Extinguishers for handover
ULC-listed ABC, K-class, CO₂ and clean agent units, matched to each space, mounted and tagged, with signage where it's missing. Pick them up at our showroom or we install on site.
Spray booths on the job? See paint booth fire suppression.
How do I get a fire alarm quote for my project?
Send the drawings through the form at the bottom of this page, using the file upload, with the address and your schedule. We review them and send a written quote; if there are no drawings yet, we can walk the site instead.
Send drawings
Electrical or architectural drawings, the occupancy, and any existing panel model if it's a renovation. A photo of the panel label is enough to start.
Layout and written quote
We lay out the devices, pick the panel and quote it line by line, with the scope split between our work and yours spelled out.
Rough-in to programming
We coordinate with your crew through rough-in, then supply, terminate and program the panel.
Verification and handover
CAN/ULC-S537 verification, a report for the inspector, and the owner's first yearly inspection booked if they'd like.
Questions from Calgary contractors
What's the difference between CAN/ULC-S537 verification and a CAN/ULC-S536 inspection?
CAN/ULC-S537 is the verification of a new or modified fire alarm system before occupancy; CAN/ULC-S536 is the yearly inspection and test of an existing system after that. On your project we do the S537 verification; the building owner then needs an S536 inspection every year.
Do you only do the fire alarm, or the electrical too?
We do the fire alarm side, not the building's general electrical. Your crew pulls the wire; we handle panel supply, device layout, terminations, programming and verification, and any suppression tie-ins.
How much does a new fire alarm system cost in Calgary?
A new fire alarm system or panel replacement typically runs $4,400 to $13,700 before GST, based on our own quotes. It varies the most of anything we price, by building size and device count, so we quote from your drawings or a site walk.
Can you replace an old conventional panel without rewiring the building?
Often, yes. The Autocall 4007ES is cross-listed with most conventional detectors and supports programmable end-of-line resistors, so it can reuse compatible field wiring and add addressable devices as areas are renovated.
Can you install the kitchen hood suppression on the same project?
Yes. We install new kitchen hood suppression for new restaurants and renovations, coordinated with you and the electrician, and wire the alarm tie-in Alberta requires. Typical installed cost is $6,000 to $12,000 depending on hood length and appliances.
Our technicians at work
Real photos of our Calgary team on the job: installs, inspections and panel builds.






Related pages for contractors
Autocall fire alarm systems
Design, install, panel upgrades, S537 verification and annual S536 inspection of Autocall addressable fire alarms.
Learn more →Fire alarm inspection
Annual CAN/ULC-S536 inspection, a full report for the Calgary Fire Department, and deficiency repairs.
Learn more →Kitchen hood suppression
Six-month inspections, new systems, replacements and repairs for restaurant hood systems.
Learn more →Fire extinguishers
Annual tagging on site or $12 per unit at our showroom, plus sales, recharges and hydro testing.
Learn more →Send your drawings for a fire alarm quote
Attach the drawings, the site address and your schedule. We work in Calgary, Airdrie, Chestermere, Cochrane and Okotoks, and reply within one business day, usually the same day.
- Written quote before any work
- Photos of every deficiency
- We book your next inspection and remind you